The Complete Lee Enfield No. 1 MKIII Restoration
April 10, 2014 56 Comments
Lee-Enfield SMLE No. 1 MKIII
For those of you who have followed along, I finally finished up the Lee-Enfield this past weekend, and I’m pretty pleased with the results. To recap, this rifle was given to me by my father-in-law back in early January. It’s a Lee-Enfield SMLE (Short Magazine Lee-Enfield) model No. 1 MKIII (.303 British caliber) produced at the Birmingham Small Arms Co. in England in 1940. Lee-Enfields were manufactured from 1888 to the early 1970s, and total production was nearly 14 million rifles. This one appeals to me because it was made in England during the Battle of Britain, and shows evidence of actual deployment in combat.
The WWII No. 1 MKIII rifles are plentiful even today, and not particularly valuable. I probably exceeded the value of this one in the parts alone that I purchased, but I didn’t restore it to sell. It’s a keeper and a shooter that will be enjoyed and passed down. As it happens, the first high-powered rifle I ever shot as a kid was an old WWI vintage Enfield that belonged to my uncle. I remember that .303 kicked like a 12 gauge. I may even still have that first casing somewhere in a box of my childhood stuff.
The Enfield before restoration with new forestock and hand guard shown above
As I wrote in earlier posts, the rifle had been ‘sporterized’ at some point, or at least someone started that process. Unfortunately, this was a popular practice in the post war years. The guns were plentiful and cheap, and guys who bought them apparently preferred the look of a traditional hunting rifle. Since the Enfield featured a barrel fully shrouded in wood, sporterizing them usually began with removing the nosecap and hardware, the upper hand guard, and cutting off the front part of the forestock. Sometimes the rear sights were removed or altered to accept a scope, but fortunately the bubba who hacked away at this rifle didn’t get that far.
The forestock had been cut, the hand guard missing
The forearm on this rifle had been cut just behind the swivel band. The entire nosecap assembly at the front was missing, along with the swivel band, forward swivels and a variety of related hardware, and the upper hand guard. The rear hand guard was still there, but its ears had been cut off and so it needed to be replaced. It appeared all of the remaining wood on the rifle was scrubbed with a heavy wire brush, leaving the surface pretty rough and scarred with brush marks. All of the original finish was long gone.
After the initial disassembly and inspection, I was happy to find the action and barrel in surprisingly good condition. Areas of rust were minimal and superficial. All the serial numbers thankfully matched, so I knew everything was likely original. The action and barrel had significant areas of olive drab paint, which I discovered was routinely applied to rifles used in tropical climates during WWII to help prevent rust. I was careful to leave that intact.
Receiver with bolt removed – original forestock still on the rifle (note the olive drab paint)
I was able to identify and source all the missing parts without too much trouble. Since there was such a long bedding space on the Enfield’s full length forestock, I decided to go with an unissued but old forestock and hand guard assembly. With so much hand fitting required, I didn’t want to take a chance on a stock that had already been on another rifle. I may have been misguided in this assumption, but that’s what I did. I left the original buttstock on the rifle since there was no need to replace it other than the aesthetic contrast between it and the new wood. I preferred to keep the rifle as close to original as possible.
Fitting the new forestock to the receiver – completed
The new wood required quite a bit of fine tuning and adjustment to get it to fit the receiver and barrel correctly. There are several fairly critical areas on Enfield rifles where the wood needs to fit very flush against the metal, so the work was slow and cautious. With so many parts all needing to come together and a half-dozen attachment points that all had to be aligned, I spent more than a few hours wondering why I ever started this project. But in the end, it all finally came together and I feel really good about the fit. It seems to fit like a glove where it’s supposed to, with the appropriate generosity in the other areas where called for.
The hand guard sat too high for the nosecap to slide on
Of everything on the rifle, the nosecap I sourced ended up being the most difficult part to get properly installed. Initially the upper hand guard sat too high for the nosecap to slip over it properly. That required carefully reducing the height of the guard along its full length, but not so much that the top of the barrel would bottom out preventing it from seating against the forearm. Once that problem was resolved, I then found that the screw holes through the forearm were just lightly out of alignment, preventing the front nosecap screw from engaging the threads on the opposite side of the nosecap. Eventually, with a lot of patience and careful filing, everything fell into place and the wood was ready for the finish.
While not the most practical by today’s standards, I wanted to keep this rifle as true to original form as possible, and so went with the tried and true linseed oil finish. This is what was used when the rifle was made. Since boiled linseed oil is chemically different, I used raw linseed oil. Or at least I assume it’s raw. I had a can of artist’s grade linseed oil that I bought when I was in college 30 some years ago and never opened. I cut it with 50% turpentine to help ensure it would dry sometime this decade. Following the old adage, once a day for a week, once a week for a month, I’ve applied about 8 ‘coats’ and the results look great. The wood has a nice rich low luster and even the contrast between the new wood and the old stock doesn’t jump out too much.
Rear Sight with new upper guard in place
I completed the restoration with an original WWII vintage Enfield sling, also dated 1940, that I found on eBay. That and the war vintage bayonet I previously wrote about are the icing on the cake. Not that I need a bayonet, but it’s in unissued condition and the price was too good to pass up. I’m looking forward to putting a couple dozen rounds down range sometime in the next few weeks.
Lee-Enfield SMLE No. 1 MKIII
***
Virginia Toolworks 
Reblogged this on Brittius.com.
LikeLiked by 1 person
Reblogged this on hocuspocus13.
LikeLiked by 1 person
Awesome job. What a great looking example of the best rifle ever made.
LikeLiked by 1 person
Thanks! I just hope it shoots okay. I’ve already got two more firearm restoration projects in the que – a WWII Japanese Ariska and a 1910s Lancaster Arms side by side 12 gauge.
LikeLiked by 1 person
Have you tried out the 303?
LikeLike
I did! I ran a few rounds through it on Easter Sunday. The rifle shoots straight enough (hard to tell exactly how accurate because I was hand holding it), but it was hitting a 6 inch target at 50 yards without any effort toward accuracy. Next time out I will shoot from a rest.
LikeLike
Good stuff. My brother and I love our Lithgow 303s but ours don’t have the cut offs as produced in 1941. Look forward to seeing how you get on with the Japanese rifle.
LikeLiked by 1 person
Here’s the link to the write-up on the Arisaka.
LikeLike
Good job again. Nice looking rifle. Pity about it not being fireable but nice for the memories. Next project?
LikeLiked by 1 person
Next (current) project is a very old 10 gauge side by side that I assume belonged to my grandfather or great-grandfather, but was left in a barn for most of the 20th century. I’m in the middle of replacing both hammers, which were long lost. Should be completed very soon.
LikeLike
Hi Bryant! I am trying to locate the full wood set and hardware for my Lee Enfield No. 1 Mk 3 SMLE that was “sporterized” as well. Do you know where I may find a wood set and hardware? My e-mail address is w7dbc@yahoo.com. Thanks, Dave
LikeLike
Brilliant work. I used to shoot these at school (in England) back in the early 1970s. We’d go out to Otley Moor, just outside Oxford, and shoot first from 200 yards then from 500 yards. As I’m left-handed I used to get horribly bruised on my left cheekbone from the slide kicking back. But it was fiercely accurate. I’m told the Afghans have only recently given up theirs!
LikeLiked by 2 people
It looks fantastic. I am doing the same to a 1914 No. 1 MkIII, so I was wondering where you sourced the furniture?
LikeLike
Got the furniture on eBay. Cost a small fortune, but it was the only place I could find what I wanted.
LikeLike
I’ve been looking there too. I think my timing has to be just right to get a full set. Thanks!
LikeLike
Numrich is good for parts too, but they rarely seem to have the furniture.
LikeLike
Great job on your Enfield . I picked up a Enfield No 2 Mk 3 22 caliber training rifle with matching numbers in G to VG condition, with 90% on the finish and from a desirable factory for $125 at a local flea market. Of course it had been sporterized and badly at best but nothing but the wood had been cut/removed so that’s a big plus. Now I need to track down and purchase all the wood and nose cap ect. and bayonet. Im aware this post is late but if anyone out there knows where i could find these parts i would appreciate the info and I can check back here under the new comments.
LikeLike
Great job on your Enfield and it was good reading. I picked up a Enfield 1915 No 2 Mk3 .22 caliber training rifle at a local outdoor flea market in G to VG condition with 90% on the metal finish with matching serial numbers all for $125 . It had been sporterized so none of it’s wood can be used, but a big plus is nothing on the rifle had been cut,removed or replaced, original sights front and rear so I figured it would be the perfect specimen for a restoration. If it hadnt been sporterized (badly) it would have been priced beyond flea market pocket money. I got it home knowing what I thought was an average amount about Enfield rifles until I seen all the stampings. I now know it started out a 303 and was converted to a 22 Cal training rifle by Parker Hale and also has an F stamped above the serial numbers but not sure if it stands for Fazakerly royal ordinance factory or if the F stands for “fine adjustment” , if anyone knows I would appreciate your knowledge . Because it’s a arsenal conversion it has it’s original stampings from starting out a 303 caliber and a second round of stampings from it’s 22 caliber training rifle conversion. I’m going to start the restoration any day now and if anybody knows of a good scorce for stocks,nose caps,swivel bands,and so on I’d appreciate the info. I will check back here. Actually after I seen what these sell for I would probably sell it for the right price or trade but until then I will start getting it back to it’s original condition and hopefully someone can steer me in the right direction.
LikeLike
I had great success finding everything I needed between Numrich and eBay. I’d start there.
LikeLike
G’day,
I am restoring a MKIII at the moment and curious as to how you sealed the metal to stop it from rusting, i love that finish!
LikeLike
Mitch, I didn’t seal it, I just cleaned it with some 000 steel wool and CLP . As long as I keep it oiled, it should be fine.
LikeLike
I have the same gun where can I get a new forstock and hand guard for this.
Thanks
Brendan King
LikeLike
I got mine on eBay.
LikeLike
I see them on eBay. How did you match the colour. The ones on eBay are very light
LikeLike
I just waited until I found one that looked close to the stock I had. Could be the ones you are seeing are not walnut. Mine wasn’t a perfect match either, but that’s the nature of walnut. It gets richer with age.
LikeLike
Where did you find the lower forearm
I can’t locate one.
I have an SMLE 1915 without the shell cut
Off or volley lever III*
LikeLike
I bought the wood furniture on eBay.
LikeLike
Do you manufacture & supply Forestock Mk111 SMLE and supply to Australia.
LikeLike
No, sorry
LikeLike
I really enjoyed this article. I recently acquired a No. 1 Mark III* that was sporterized sometime in the past. I think that your approach to restoring yours is perfect and mirrors what I have in mind for mine. Thanks for posting this.
LikeLike
Hi,
I have a SMLE no.1 mk3*. The top two hand guards have been replaced and no longer have the correct size cut out to accept the original rear sight. Also the rear sight has been replaced with a fixed post instead. Would you be able to tell me where you sourced the replacement top wooden hand guards from? Thanks.
LikeLike
I got mine on eBay. You might also check Numrich and Sarco for the parts you need.
LikeLike
Where did you ever find a replacement fore stock ?
LikeLike
eBay
LikeLike
Hi. I know you posted this like 4 years ago but I was wondering if I could pick your brain a bit regarding a restoration project I am doing with my 1mk3. I would really like to talk with you about the parts you used and where you found them but I am apprehensive about ordering the parts until I know exactly what I should buy. You project was very impressive and I would like to do the same thing.
LikeLike
I’d like to add that, I wanted to give you a picture of my rifle and conclusively determine that it is actually a 1mk3. I look forward to hearing from you. Thank you in advance.
LikeLike
I’m not expert, but you can email me using the contact link and I’ll do what I can to help.
LikeLike
Great article. One question. I have 2 smle. One 1914, other 1944.first bsa, 2nd lithgow. The bsa was sporterized and i want to return it to original image. But the bsa barrel is approx 1 1/2 shorter then the Lithgow. How can i find wood to fit the shorter bsa. I have seen earlier models with a designations of sht. Both are no1 mk 3. Would that sht stand for short?
LikeLike
Sorry, I’m not an expert on Enfields. There are numerous websites you can research to find this information.
LikeLike
Have restored many NO I’s and NO IV’s. Wood used to be pretty plentiful. Low wood is very difficult to find. Liberty Tree Collectors have a decent hard parts selection some top wood. Sarco Inc has decent metal as well. Gun Parts Corp noted above metal to Check BRP also. More likely to find wood for the NO IV’S. Actually have some low wood out to see if it can be copied by a stock maker for a NO I MK V. There was a company in England where one could get reproduction wood for the SMLE’s. The owner passed a year or so ago but there was a possibility the family will continue. Otherwise am looking locally. Used to think these Brits were ugly but they are like worms they get under your skin. Just plain iconic and reliable as the day is long.
LikeLike
Good Afternoon & well done,
I have had trouble in obtaining the lower stock from Liberty due to US export Regulations. However I managed to obtain lower stock parts within Australia.
We now have a replica WW1 Uniform and Arms supplier that markets complete wood sets for App $400.00 AUD that helps. In addition parts are available for all weapons particularly SMLE.
I have completed restoration of Two Replica, SMLEs’ Mk11 & Mk111. After the recent 100 year centenary of WW1 & Gallipoli celebrations there are now available Original-SMLE 303 Rifles for sale within Australia, however you must have a Police Commissioners Licence to Purchase,(in all Australian States) also to retain in a safe & Licenced Armoury. You must also hold a collectors Licence and be a Financial member of a Rifle Club. You also require a permit to carry in public in going to, or from a specific destination (practise or hunting)or at a Military or any other ceremonial parade.
As you see our Australian Gun Laws are very strict. Good luck and well done in your restoration.
Yours Sincerely.
Lt. Leonard Carter.AFSM EFO JP, (Retd).
President/CO. 7th Light Horse Regiment AIF. Menangle Historical Troop. Australia.
LikeLike
Nice restore job. I am working on 2 and having trouble finding the mark 3 fore end and front handguard If you still have the cut down fore end I would like to buy if you want to sell it.
LikeLike
Sorry, I sold those parts on eBay right after I finished the restoration.
LikeLike
I have a Britich 303 Mark3 Doues aney 1 no the seating Death
LikeLike
I have no idea what this means.
LikeLike
This was awesome, thanks for posting this, it was a big help for restoring my own SMLE No1 Mk3.
LikeLike
Could you please advise me on how to identify a WWI bolt action rifle that has been handed down in my family? My grandfather fought in WWI and I am assuming that it is perhaps his or one he used during his service. It looks much like the Lee-Enfield bolt action rifle but the markings on the stock and sighting mechanism are different from what I have observed during my own research so perhaps not a British or American-made Enfield.
Curious. Any pointers would be a great help. Thank you.
LikeLike
This looks amazing! I’ve got a 1934 Mk3 that needs a resto. Do you have links and stuff for where you may have found parts? I realize that this was written almost a decade ago. Thanks.
LikeLike
I got all my parts on eBay and Numrich. You might have to do some searching.
LikeLike
In February 2022 it is rather late in the day for a comment, but I was lucky to find a BSA Lee Enfield number 1 mark lll* made in 1941 in authentic condition, except that it was re-barreled, and 2 holes for a scope mounting was drilled and tapped on the front of the receiver. I originally made the mistake of replacing the rear sight (non-windage adjustable) with the rear sight off a number 4. At first test shooting the rifle I found the number 4 rear sight slightly higher than the number 1’s, which caused the rifle to shoot about 8 inches high at 100 metres. I since changed the rear sight back to the original. I love my LE number 1 mark lll*. The rear sight mounted towards the centre of the rifle suits my far-sighted ageing eyes a lot better than the number 4’s sights mounted up close to my eyes.
LikeLike
P S: I notice you have the windagecadhustable sight on your restored rifle as well, didn’t you find it shoots high?
LikeLike
Nope, that’s the sight that came on it. Shoots just fine.
LikeLike
I have 1941 MA LITHGOW SMLE III AUSTRALIA RIFLE
miss placed bolt. Can you get me one?
Carl Hayner
951-704-0135
Text
LikeLike
Sorry, I don’t sell gun parts.
LikeLike
Going through the same right now, been some rough going but it seems to be coming together.
LikeLike
The SMLE was the bolt action rifle you wanted in WW1 & WW2, not the Mausers. I’m hoping my to finish off my own restoration this year. I bought an RFI Ishapore 1944 barreled action a while ago & I’ve been slowly buying parts to complete it. I’ve only the front hand guard, barrel band & stacking swivel to go.
LikeLike